manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 71

Drum Assembly

g258878

Figure 28

1.

Transmission gear box assembly

5.

Lock nut (2 each)

9.

Frame assembly

2.

Traction drum

6.

Shoulder bolt (6 each)

10.

Shoulder bolt (2 each)

3.

Splined coupler (4 each)

7.

RH hex shaft

11.

Truss screw

4.

Washer (4 each)

8.

Drum drive gear box assembly (2
each)

12.

LH hex shaft

Removing the Drum Assembly

Note:

Refer to

Figure 28

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Remove the LH and RH drum drive gear box assemblies (item 8 in

Figure

28

); refer to

Removing the Drum Drive Gear Box Assembly (page 5–11)

.

3. Remove the traction drum (2) from the frame assembly (9).

Greensmaster

®

1018/1021/1026

Page 5–17

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands