manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 59

Service and Repairs

Reel Drive Belt

g258535

Figure 21

1.

Reel drive box assembly

4.

Bolt

7.

Socket head screw (3 each)

2.

Reel belt

5.

Gasket

3.

Idler arm

6.

Reel drive cover

The greensmaster machines use a positive drive belt on the right side of the
machine to operate the cutting unit.

Removing the Reel Drive Belt

Note:

Refer to

Figure 21

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Remove the 3 socket head screws (7) that secures the reel drive cover (6)

to reel drive assembly (1) and remove the reel drive cover to expose the
reel drive belt (2).

Greensmaster

®

1018/1021/1026

Page 5–5

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands