manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 65

Drum Drive Gear Box Assembly

g258813

Figure 25

1.

Transmission gear box assembly

5.

Lock nut

9.

Frame assembly

2.

Traction drum

6.

Shoulder bolt (3 each)

10.

Shoulder bolt

3.

Splined coupler (2 each)

7.

RH hex shaft

11.

Truss screw

4.

Washer

8.

Drum drive gear box assembly

Removing the Drum Drive Gear Box Assembly

Note:

Refer to

Figure 25

during this procedure.

1. Park the machine on a level surface. Ensure that the engine is OFF. Remove

the spark plug wire from the engine spark plug.

2. Remove the transport wheel if attached; refer to

Removing the Transport

Wheel (page 7–27)

.

Note:

Support the machine on kickstand during this operation.

3. Move the traction engage/disengage lever to the disengage position to

remove torque from the drum drive gears.

Greensmaster

®

1018/1021/1026

Page 5–11

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands