Toro Greensmaster 1018 Service Manual Download Page 80

Page: 80 / 179

Disassembling the Transmission Gear Box Assembly

g259588

Figure 33

Retaining ring

11.

Grease seal

21.

Brake mount pin

Spacer bushing

12.

Ball bearing (2 each)

22.

Transmission gasket

O-ring

13.

Spacer

23.

Transmission cover

Straight bushing (2 each)

14.

Oil seal (2 each)

24.

Socket head screw (12 each)

Retaining ring (2 each)

15.

Oil seal

25.

Ball bearing (2 each)

Oil seal (2 each)

16.

Sleeve bushing (2 each)

26.

Transmission housing

Flange bushing (2 each)

17.

Dowel pin

27.

Hollow hex plug (2 each)

ORB plug

18.

O-ring seal

28.

E-ring

Detent spring

19.

Traction selector shaft

10.

Detent ball

20.

Groomer pin

Note:

Refer to

Figure 33

during this procedure.

1. Remove the 2 hollow hex plugs (item 27 in

Figure 33

) from the transmission

gear box assembly (26).

2. Remove the 12 socket head screws (24) that secures the transmission

cover assembly (23) to the transmission housing assembly (26). Remove
the transmission cover assembly and transmission gasket (22) from the
transmission housing assembly. Discard the transmission gasket (22).

Traction and Reel Drive Systems: Service and Repairs

Page 5–26

Greensmaster

1018/1021/1026

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Search results

Summary of Contents for Greensmaster 1018

Reviews:

Brands by name

Popular brands

Toro Greensmaster 1018, Service Manual

Search results

Summary of Contents for Greensmaster 1018

Reviews:

Brands by name

Popular brands