manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 111

Removing the Brake Cable (continued)

g261858

Figure 51

1.

Retaining ring

3.

Brake lever

5.

Brake cable

2.

Cable eyelet

4.

Jam nut

3. Remove the brake cable (item 5 in

Figure 51

) from the brake lever shaft on

the transmission gear box assembly as follows:

A. Loosen the front cable jam nut (4) that secures the brake cable to the

casting slot on the transmission gear box assembly. Remove the brake
cable from the slot.

B. Remove the retaining ring (1) that secures the cable eyelet (2) to the

brake lever (3) on the transmission gear box assembly.

C. Remove the brake cable eyelet (2) from the brake lever (3).

4. Remove the control cover and lower cover from the handle assembly to allow

access to upper end of the brake cable.

5. Remove the brake cable (item 9 in

Figure 50

) from the brake lever assembly

as follows:

A. Loosen the lower brake cable jam nut (8) that secures the brake cable

(9) to the upper receiver weldment (4). Slide the brake cable from the
upper receiver weldment.

B. Remove the brake cable spring (7) from the spring anchor on the brake

lever assembly (3). Note the orientation of the brake cable spring hook
on the brake lever assembly for assembly purpose.

6. Remove the brake cable (9) from the machine.

Greensmaster

®

1018/1021/1026

Page 7–7

Controls, Wheels and Accessories : Service and Repairs

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands