manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 132

Removing the Transport Wheel (continued)

g200276

Figure 64

1.

Wheel retaining lever

3. Pivot the wheel retaining lever away from the center of the wheel. Slide the

transport wheel off the wheel hex shaft.

Disassembling the Transport Wheel

g261682

Figure 65

1.

Wheel hex shaft

1. Ensure that the tire is fully deflated before disassembly of the wheel.

2. Remove the 3 bolts and 3 lock washers from the shallow rim and hub.

Remove the hub from the deep rim.

3. Inspect the hub bushing. Replace the bushing, if worn or damaged.

4. Remove the 4 bolts and 4 flange nuts from the deep rim and shallow rim.

Remove the shallow rim from the deep rim.

5. Separate the tire, tube and deep rim.

6. If necessary, remove the shoulder screws, torsion spring, and retaining lever

from the hub.

Controls, Wheels and Accessories : Service and Repairs

Page 7–28

Greensmaster

®

1018/1021/1026

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands