manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 145

Installing the Bedbar Adjuster

1.

If previously removed, secure the detent (3) to the side plate (12) with the

bolt (4).

2.

If previously removed, align the key on the flange bushings (2) to the slots in

the cutting unit side plate (12) and install.

3. Slide adjuster shaft (1) into flange bushings (2) and secure with a wave

washer (5) and a retaining ring (6).

Note:

The bedbar adjuster shaft (1) has left-hand threads.

4. Apply anti-seize lubricant to the threads of the bedbar adjuster screw (7)

that fit into adjuster shaft (1) (the left hand threads) and thread the bedbar
adjuster screw into the adjuster shaft.

5. Install the washer (9), compression spring (10) and lock nut (11) onto the

adjuster screw (7).

6. Install the bedbar (8); refer to

Installing the Bedbar (page 8–8)

.

Greensmaster

®

1018/1021/1026

Page 8–11

DPA Cutting Units: Service and Repairs

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands