manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 69

Assembly of Drum Drive Gear Box Assembly

g263151

Figure 27

1. Install the ball bearings (23), wave washer (24) and spur gear (21) to the

drum drive housing (25).

Note:

The outer diameter and inner diameter of the ball bearings (23) must

be slip fit.

2. Install the retaining ring (26) to the spur gear (21). Apply a light coat of oil to

the oil seal (27). Install the oil seal (27) and retaining ring (28) to the drum
driving housing (25).

3. Use a press to install the ball bearings (19) to the spur gear (20). Install the

retaining rings (18) to spur gear (20).

Note:

The inner diameter of the ball bearing (19) must be slip fit.

4. Apply a light coat of grease and install the O-ring (32) to the bearing pin (31).

Install the bearing spacer (34), spur gear (20) onto the drum drive housing
(25) and secure with the bearing pin (31) and nut (17).

5. Install the ball bearings (6), bearing spacer (7), spring washer (9) and drum

drive shaft (5) to the drum drive housing (25).

Note:

The outer diameter and inner diameter of the ball bearings (6) must

be slip fit.

6. Install the V-ring seal (4) onto the drum outer hub (3). Install the key (30) to

the drum drive shaft (5) and apply anti-seize lubricant at the top of the key.
Slide the drum outer hub (3) to the drum drive shaft (5) and secure with
the washer (2) and nut (1).

7. Install the oil seal (10) into the drum drive housing (25). Install the key (30)

to the drum drive shaft (5) and apply anti-seize lubricant at the top of the
key. Slide the spur gear (11) to the drum drive shaft (5) and secure with
the nut (12).

8. Torque tighten the nut (17) from

36.5 to 44.7 N·m (27 to 33 ft-lb)

.

9. Hold the nut (12) and torque tighten the nut (1) from

74.5 to 88 N·m (55

to 65 ft-lb)

.

10. If removed, install the oil seal (13) to the drum drive cover (14).

11. Install the gasket (8) to the drum drive housing.

Greensmaster

®

1018/1021/1026

Page 5–15

Traction and Reel Drive Systems: Service and Repairs

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands