manualshive.com logo in svg

TIPTEL .comPact 42 IP 8, Installation Manual, Page: 95 / 136

Share
Download
TIPTEL .comPact 42 IP 8 Installation Manual Download Page 95

Menu: Subscriber 

95 

caller’s outgoing MSN (subscriber 50 calls the 930 => subscriber 50's answer-
ing machine moves to remote access). 

 

In configuration you have activated the remote access and entered a remote 

access code. After a call you can now enter the remote access code during the 
OGM to enter remote access mode. 

 
QRC-(Quick Remote Control) 

The QRC (quick remote access) number allows you to carry out remote access ex-
ternally without entering the remote access code. For example, if you have entered 
your mobile phone number and call the answering machine from your mobile you are 
recognized as being authorized for remote access and can start up remote access 
without entering the remote access code. It is not possible to enter an internal sub-
scriber call number. You can use the "remote access via 930" function to remotely 
control your answering machine internally. 

Remote control using  930 

You can activate a simple remote access to your answering machine here. After acti-
vation and calling 930 you can directly enter remote access for your answering ma-
chine. Authentication occurs via the outgoing MSN of your telephone. 

Remote access code 

The remote access code is a 1 to 4 digit number between 0 and 9999.  

Remote control 

You can switch remote access on and off here. This switch does not apply to remote 
access via 930 or QRC. 

Remote activation of VB 

You stipulate here whether remote activation of telephone answering should be poss-
ible here. For the "Yes" setting the answering machine answers a call after 50 
seconds even if telephone answering is switched off and waits for a remote access 
code to be entered. This is how to switch on telephone answering remotely. 

Note: 

The answering machine now rings in parallel to the subscriber. A call 
then receives a dial tone although the subscriber is busy and call wait-
ing has been deactivated. The "call deviation on busy" setting is there-
fore not carried out.  

Remote deletion 

You can set here whether the "Delete ICMs remotely" option is activated or not. 

Summary of Contents for .comPact 42 IP 8









































































































































Reviews:

No comments