manualshive.com logo in svg

TIPTEL .comPact 42 IP 8, Installation Manual, Page: 123 / 136

Share
Download
TIPTEL .comPact 42 IP 8 Installation Manual Download Page 123

Appendix 

123 

 

 

No 

B channel 

LCR 

***

 

Yes

No 

Dial 

Call number as per 
table or first MSN of 
the connection 

Line 

key?**** 

****

 

Yes

The selected call 
number is transmitted 

*** If an external call is established explicitly via 
an So port/B channel (function key for system 
telephones or automatically via the LCR; the de-
vice will still attempt to transmit the outgoing 
number as per the table (or any). If the table still 
does not contain the So port/B channel that is 
chosen, the first MSN of the connection of the 
connection used will be transmitted. The table 
can be found under „Subscriber settings –

 Outgo-

ing call numbers

“

 in administrator mode.

 

Call number as per 
table or any

 

**** If an external call is established via the explicit 
use of a certain call number (line key, function key 
for system telephones), the call number that is se-
lected will be transmitted. 

Summary of Contents for .comPact 42 IP 8









































































































































Reviews:

No comments