❏
1) Remove
the barrel
,
twist counterclockwise.
❏
2) Remove left side receiver
grip
two bolts
.
❏
3) Remove tank adapter
2 bolts
.
❏
4) Loosen all 6 receiver bolts
/
holding marker together with 1/8" Allen
wrench. Note: Front Grip
comes off -
at reassembly, longest bolt
goes in front grip.
❏
5) Carefully lift left receiver half
off marker.
❏
1) Double check that all other parts: Front Sight, Front Site Pin, Front
Sight Spring, Ball Latch, Front Bolt*, Linkage Arm, Rear Bolt*(+Rear Bolt
Insert on non-A.C.T. markers), Drive Spring* & Guide Pin*, Buffer O-ring,
End Cap, Rear Sight and 2 Tank Adapter Nuts {and for markers with Anti-
Chop Technology: the Spring Cup*, Upper Spring (long)*, Spring Pin*, Upper
Spring (short)*, and Linkarm Pins*(2); are in place /(*=oiled)}.
❏
Refer to the
marker owner's manual for details if needed.
❏
2) Place battery connector
through left receiver half
❏
make sure the
magnet fits into left receiver half slot so it does not break and
❏
wires are not
pinched as you
❏
place left half on right half so the halves fit flush.
❏
3) Insert 5 short receiver bolts
.
❏
Insert front grip
and
❏
insert
long receiver bolt
to hold grip. For ease of installation tighten the bolt
over the trigger first, then tighten 5 remaining bolts.
❏
4) Attach adapter
with 2 bolts
.
❏
5) Install barrel
.
❏
6) Attach 9v battery to battery connector
and be sure
wires lay flat inside the cutout area
of receiver (see STEP 3:).
❏
7) Carefully tilt and insert battery (wire attached end first
)
into receiver.
❏
8) Install left receiver grip
with 2 bolts
.
Installation is complete, continue on page 7-E Operating Instructions.
❏
7) Remove trigger
& trigger spring
.
❏
Remove trigger slider
, slider spring
and 2
slider pins
from trigger.
❏
8) Remove old sear and sear spring
from right
receiver. If black dowel pin
comes out, reinsert it.
TIME SAVER: It is Not necessary to remove additional
parts to install this kit.
❏
6) Remove rectangular knockout plate
from
left receiver half
for battery insertion.
❏
Place left receiver half
inside up with
knockout plate
flush on a flat surface.
❏
Then with a hammer and punch, start in one
corner of the plate
and carefully tap it loose
by working your way around the plate edge....
until it is removed.
❏
1) Place solenoid
/
armature
into position in
right receiver
.
❏
2) Insert Magnet
into slot
below armature.
❏
3) Carefully align and insert
computer board
into slot.
❏
4) Place trigger switch
on
2 pins of right receiver half.
❏
5) Insert capacitor
in slot.
❏
6) Route wires in cutout areas
to lay
flat under armature pin
and battery (and not
be pinched when receiver halves are reassembled.
❏
Visually inspect internal wires for disconnected
wire end(s)
or damage.
❏
7) Insert armature pin
into slots so it moves freely.
❏
8) Double check that all parts are in place as shown.
❏
9) Install trigger
and trigger spring
into the right receiver half
.
❏
10) Install new sear
and new sear spring
into right receiver half
.
❏
11) Install trigger guard
.
STEP 3: Install Sear Tripper Assembly, Magnet & Armature Pin
STEP 4: Reassemble Receiver Halves
Do not operate sear tripper assembly uninstalled as solenoid /armature
may pinch you.
3-E Custom
TM
(continued on page 7-E)
(98 CUSTOM
TM
INSTALLATION INSTRUCTIONS continued from page 2-E Custom
TM
)
E
N
G
L
I
S
H
❏
Set up a table with plenty of space to work. You will need two allen
wrenches (
) 1/8" and 5/32", hammer, punch, and a 9 volt battery.
NOTE: Carefully hand start threaded parts, do not over tighten and strip threads.
Disassemble the marker: With Air Source removed & marker in the
uncocked position
as per STEP 1;
STEP 2: Prepare Marker for kit installation.
2-E Custom
TM
(continued on page 3-E Custom
TM
)
(98 CUSTOM
TM
INSTALLATION INSTRUCTIONS continued from page 1-E Custom
TM
)
E
N
G
L
I
S
H
❏
1) Prepare Your Marker For Safe Disassembly:
❏
Follow the
instructions in STEP 1.
❏
2) Remove Battery Clip / Battery From Marker:
❏
Remove left grip
2 bolts
.
❏
Carefully work the battery out of the receiver cutout bringing
non-connected end out first. As you remove battery from receiver, do not
pull wires off of internal components.
❏
Carefully remove old battery from
battery clip connector.
❏
3) Install the New Battery:
❏
Follow instructions in: STEP 4: 6), 7), & 8).
9 VOLT BATTERY REPLACEMENT
