TIDI Zero-Gravity ZGCM-48 Instructions Manual Download Page 29 | Manualshive

Page: 29 / 45

background image

Zero-Gravity® Radiation Protection System Uncrating Instructions

29

Floor & Ceiling Mounted Units

ZGM-6-5H | ZGHSA | ZGCM-HSA | ZGCM-48 | ZGCM-66

Unpack the Body Shield Assembly

CAUTION: HEAVY EQUIPMENT

Use care when handling leaded body shield assembly. The assembly

weighs ~ 54 pounds (24.5 kilograms) and must be handled by two people.

WARNING! RADIATION DAMAGE HAZARD

The Body Shield must be handled with care to avoid damage to the Body

Shield protective lead material. If the Body Shield is damaged, it must be

inspected according to the Body and Face Shield Fluoroscopy Inspection

section of the User’s Guide (TIDI Products document 84000).

1. Remove the screws that secure the Straps (shown in red) to the Body Shield.

2. Leaving the protective foam cover intact (Figure 19), remove the body shield

assembly from the crate and place on a clean, flat surface Protective covers

remain until installation is complete.

Figure 19

Screws

Straps

Protective Foam Cover

«
...
27
28
29
30
31
...
»

Summary of Contents for Zero-Gravity ZGCM-48














































Reviews:

No comments

Related manuals for Zero-Gravity ZGCM-48

Brand: Laica Pages: 4

Brand: Varec Pages: 74

Brand: Halyard Pages: 84

Brand: PAIDI Pages: 48

D-IMager EKL3104

Brand: Panasonic Pages: 13

Brand: Labokey Pages: 5

Brand: E-Z Trail Pages: 8

Brand: B&K Pages: 10

Brand: XM Fitness Pages: 10

Brand: Parker Pages: 64

Brand: Parker Pages: 40

Matrx Digital MDM

Brand: Parker Pages: 20

Brand: Waters Pages: 250

Brand: Waters Pages: 141

FLEX-FOOT ASSURE

Brand: Össur Pages: 82

Brand: Össur Pages: 32

Digital Measuring System forUnloader & CTi CM...

Brand: Össur Pages: 6

DH Offloading Post-Op StyleShoe

Brand: Össur Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands