TIDI Zero-Gravity ZGCM-48 Instructions Manual Download Page 11 | Manualshive

Page: 11 / 45

background image

Zero-Gravity® Radiation Protection System Uncrating Instructions

11

Floor & Ceiling Mounted Units

ZGM-6-5H | ZGHSA | ZGCM-HSA | ZGCM-48 | ZGCM-66

CAUTION: HEAVY EQUIPMENT

Use care when handling leaded body shield assembly. The

assembly weighs ~ 54 pounds (24.5 kilograms) and must be

handled by two people.

CAUTION! HEAVY EQUIPMENT

Use care when handling the base. The base weighs ~660 pounds

(300 kilograms) and is not intended to be lifted.

WARNING! RADIATION HAZARD

The body shield must be handled with care so that it is not

damaged due to contact with other objects. If the body shield is

damaged, it must be rechecked according to the Maintenance

section of the User’s Guide (TIDI Products document 84000)

CAUTION! PINCH POINT HAZARD

Never push or pull a Zero-Gravity floor unit by placing hands on

the large D-shape base. The casters may swivel and pinch hands

or fingers.

ATTENTION!

DAMAGE CAN OCCUR IF THE BODY SHIELD IS ALLOWED TO

DRAG ACROSS THE SIDE OF THE CRATE.

«
...
9
10
11
12
13
...
»

Summary of Contents for Zero-Gravity ZGCM-48














































Reviews:

No comments

Related manuals for Zero-Gravity ZGCM-48

Brand: Waterwise Pages: 12

Brand: ParaBody Pages: 38

Brand: Rath Pages: 3

Brand: UFO Pages: 16

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: AcceleDent Pages: 3

Brand: Zero 88 Pages: 32

Brand: Obdstar Pages: 42

Brand: Park House Healthcare Pages: 12

Brand: ABB Pages: 33

Brand: Össur Pages: 98

Flex Foot Cheetah

Brand: Össur Pages: 107

Brand: Össur Pages: 38

Brand: Össur Pages: 39

Bionic Symbionic Leg

Brand: Össur Pages: 2

Brand: Össur Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands