manualshive.com logo in svg

Tianlong Gentier 48E, User Manual

Share
Download
Tianlong Gentier 48E User Manual Download Page 5

 

V 

Gentier Real-Time PCR System 

  European Community Representative

:

 

indicates the authorized representative of 

this instrument in European.

 

 

CE Mark

: indicates this instrument is in conformity with the  essential  health and 

safety requirements set out in European directives.

 

 

Serial Number

: indicates the serial number of this instrument.

 

 

Manufacturer

: indicates the manufacture of this instrument.

 

 

Caution

: indicates the “caution”of this instrument .

 

 

Manufacture Date

: indicates the manufacture date of this instrument.

 

 

Consult Instructions for Use

: indicates the consult instructions for the use of this 

instrument.

 

 

Separate Collection for this Equipment

: indicates that this instrument is reusable 

and not contaminated at the end of the instrument life.

 

 

 

 

Summary of Contents for Gentier 48E












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands