manualshive.com logo in svg

Tianlong Gentier 48E, User Manual

Share
Download
Tianlong Gentier 48E User Manual Download Page 21

 

7 

Gentier Real-Time PCR System

 

 

 

B. Gentier Instrument Installation   

1. Unpacking Instructions 

The  Gentier  transport  package  is  as  shown  in  figure  B-1.  The  Gentier  instrument  and  its 
accensories are well preserved in a carton case. In order to prevent the collision and oscillation 
during transportation, the Gentier instrument is sealed with plastic bag and well supported by 
protective foams.   

 

Figure B-1. Package Details 

 

1.1 Unpacking Steps 

The unpacking of the Gentier transport package mainly includes 4 steps, as shown in figure B-2. 
The specific operation method is as follow.   

1

st

 Step

:

 

cut off the packing belt and unseal the transpot package.   

2

nd

 Step

:

 

take  out  the  instrument  accessories  and  remove  the  protective  foam  on  top  of  the 
instrument.. 

3

rd

 Step

:

 

hold the Gentier instrument on both sides and take it out of the carton. 

4

th

 Step

:

 

remove the plastic bag and place the instrument on steady plane.

   

Summary of Contents for Gentier 48E












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands