Ti Lite AERO Z Owner'S Manual Download Page 52

Page: 52 / 147

4-10

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 4: BACKRESTS And PUSH HAndLES

Replacing the Backrest

(Aero Z Series 1, ZR Series 1, ZRA Series 1)

Tools Needed:

• 7/16” Open End Wrench

• 5/32” Allen Wrench

1. Remove the backrest upholstery. See “Velcro

-Style Adjustable Back Upholstery” or “Tension Adjustable by

Straps Back Upholstery” on pages 7-1 to 7-3.

2. Remove the backrest posts. See “Adjusting the Backrest Height” on pages 4-4 to 4-9.

Note: If your original backrest was Titanium and is being replaced by a new Titanium backrest, you will need to

remove the end plugs from your old backrest and install the end plugs in your new backrest.

3. Remove the backrest sleeves. See Figure 4-9.

4. Remove the two Allen screws that secure each bracket to the backrest. Note the order of the washers and

spacers and the position of the backrest cord, if any. See Figures 4-10, 4-11 and 4-12.

5. Install the new backrest and securely tighten the Allen screws removed in Step 4.

6. Install the backrest sleeves in the new backrest.

7. Reinstall the backrest posts removed in Step 2.

8. Reinstall the backrest upholstery removed in Step 1.

Replacing the Backrest

(Aero Z Series 2, ZR Series 2, ZRA Series 2)

Tools Needed:

• 5/32” Allen Wrench

1. Remove the backrest upholstery. See “Velcro

-Style

Adjustable Back Upholstery” or “Tension Adjustable by

Straps Back Upholstery” on pages 7-1 to 7-3.

2. Remove the backrest posts. See “Adjusting the

Backrest Height” on pages 4-8 and 4-9.

3. Remove the backrest sleeves. See Figure 4-14.

4. Remove the two Allen screws (one on each side of the

chair) and remove the backrest. See Figure 4-15.

5. Install the new backrest and securely tighten the two

Allen screws.

6. Install the backrest sleeves in the new backrest.

7. Reinstall the backrest posts.

8. Reinstall the backrest upholstery.

WARNING

The threads on the Allen screws that secure the backrest posts to the backrest have been treated with a Vibra-TITE

VC-3, a locking and sealing coating, to reduce the possibility that they will become loose. TiLite requires that

you reapply Vibra-TITE

VC-3 each time your backrest is replaced.

If you ignore this Warning, your backrest posts

could become loose or disconnected from the wheelchair, and you could fall, tip over or lose control of the wheelchair

and seriously injure yourself or others or damage the wheelchair.

Figure 4-15

Replacing the Backrest

Allen

Screws

Summary of Contents for AERO Z




















































































































































Search results

Summary of Contents for AERO Z

Reviews:

Related manuals for AERO Z

Brands by name

Popular brands

Ti Lite AERO Z, Owner'S Manual

Search results

Summary of Contents for AERO Z

Reviews:

Related manuals for AERO Z

Brands by name

Popular brands