manualshive.com logo in svg

Ti Lite AERO Z, Owner'S Manual, Page: 87 / 147

Share
Download
Ti Lite AERO Z Owner'S Manual Download Page 87

8-7

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER  8:  AXLE  PLATES  AND  CAMBER  PLUGS                          

(CENTER OF GRAVITY; REAR SEAT HEIGHT)

Adjusting the Center of Gravity
(ZR Series 2)

I

WARNING

When repositioning the camber clamps on the CG Brackets, always leave as many open holes between the two Allen 

screws as your desired placement will permit.  NEVER use two adjacent holes to attach the camber clamps to the CG 

Brackets.

  If you ignore this Warning, your camber clamp may fail, causing you to fall, tip over or lose control of the 

chair and seriously injure yourself or others or damage the chair.

Tools Needed:

•  5/32” Allen Wrench

• Ruler

1.  Remove the rear wheels.

2.  Remove the four Allen screws (two on each side) that secure the camber clamps to the CG brackets.  See Figure 

8-10.

3.  Reposition the camber clamps to the desired position on the CG Brackets, making sure the positioning is identical 

on both sides of the chair.  You MUST leave one open hole between the two Allen screws.

4.  Reinstall the Allen screws and lock washers and securely tighten all four Allen screws.

5.  Reinstall the rear wheels.

6.  Check the toe-in/toe-out and adjust as needed.  See pages 8-8 and 8-9.

 

     

 

          

Figure 8-10

Adjusting the Center of Gravity

CG Bracket

Camber Clamp

Washers

Allen Screws

Open Hole

(Required)

Replacing the Camber Tube 

(ZR Series 2)

Tools Needed:

•  3/16” Allen Wrench

•  5/64” Allen Wrench

• Ruler

1.  Remove the rear wheels.

2.  Using the 5/64” Allen wrench, remove the bumper assembly, making note of the order in which the parts are 

assembled.

3.  Loosen, but do not remove, the Allen screw that secures the camber tube to each camber clamp.  See Figure 

8-11.

4.  Remove the camber tube.

Summary of Contents for AERO Z




















































































































































Reviews:

No comments