manualshive.com logo in svg

Ti Lite AERO Z, Owner'S Manual

Share
Download
Ti Lite AERO Z Owner'S Manual Download Page 43

4-1

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 4: BACKRESTS And PUSH HAndLES

Folding Adjustable Height & Angle Backrest 

(Titanium or Aluminum)

Note: The Aluminum Adjustable Height & Angle Backrest without Integrated Push Handles is standard on all 

wheelchairs.  The Titanium Adjustable Height & Angle Backrest is available as an option on all chairs.  Integrated 

Push Handles are available as an option with either the titanium or aluminum backrest.  The instructions in this section 

apply to all of these variations.

I

WARNING

Before using your wheelchair, make sure the Folding Adjustable Height & Angle Backrest is locked securely in place 

in the upright position and all mounting hardware is securely tightened.  

If you ignore this Warning, you may fall, tip 

over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Folding the Backrest

1.  Grasp the TiShaft Release Bar and pull up.  See Figures 4-1 and 4-2.

2.  Push the backrest forward toward the front of the chair.

Note:  If you have a Lock-Down Backrest, make sure the backrest is locked securely in the folded position.

Unfolding the Backrest

1.  Lift up on the backrest and pull towards the rear of the chair.

2.   Make sure the backrest locks securely into place.

Unfolding the Lock-Down Backrest

1.   Push up the TiShaft Release Bar and pull the backrest towards the rear of the chair.

2.   Make sure the backrest locks securely into place.

  

Figure 4-2

Aero Z/ZR/ZRA Series 2 Folding Adjustable Backrest 

with TiShaft Release Bar

TiShaft

Release Bar

Backrest

Figure 4-1

Aero Z/ZR/ZRA Series 1 Folding Adjustable Backrest with 

TiShaft Release Bar

TiShaft

Release Bar

Backrest

Summary of Contents for AERO Z




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands