manualshive.com logo in svg

Ti Lite AERO Z, Owner'S Manual

Share
Download
Ti Lite AERO Z Owner'S Manual Download Page 48

4-6

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 4: BACKRESTS And PUSH HAndLES

 

     

Figure 4-9

Adjusting the Backrest Height

Figure 4-10

Adjusting the Backrest Height

Backrest Post

Backrest Post

Backrest

Bracket

Locknut

Allen

Screw

Backrest Sleeve

Backrest

Threaded Post

Plug

Second

Lowest

Hole

Top End Cap

Short End Plug

Long End Plug

3.  If your backrest is set to 8-½” and if you are setting the backrest at 10” to 12-½”:

a.  Remove the top end caps.  See Figure 4-9.

b.  Install the backrest sleeve in each backrest tube.  See Figure 4-9.

c.  Keeping the threaded post plugs on the bottom end of the backrest posts, insert the backrest posts 

into the backrest.

d.  Align the backrest posts inside the backrest so that the desired hole in the backrest post aligns with 

one of the upper 3 holes in the backrest.  See Figure 4-11.

e.  Secure the backrest posts inside the backrest and the backrest to the bracket using the Allen screws. 

See Figure 4-11. Proceed to Step 7.

Figure 4-11

Adjusting The Backrest Height

Backrest Post

Three 

Upper 

Holes

Backrest

Bracket

Allen 

Screw

4.  If your backrest is set to 9” or 9-½” and if you are setting the backrest at 8-½”:

a.  Remove the backrest from the backrest brackets.  See “Replacing the Backrest” on page 4-10.

b.  Remove the backrest posts from the backrest.  See Figure 4-9.

c.  Remove the backrest sleeves from the backrest.  See Figure 4-9.

d.  Insert the top end caps in the backrest.  See Figure 4-9.

e.  If the backrest is titanium, remove the short end plugs (see Figure 4-9) and install the long end plugs 

in the bottom ends of the backrest.

Summary of Contents for AERO Z




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands