manualshive.com logo in svg

Ti Lite AERO Z, Owner'S Manual

Share
Download
Ti Lite AERO Z Owner'S Manual Download Page 83

8-3

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER  8:  AXLE  PLATES  AND  CAMBER  PLUGS                          

(CENTER OF GRAVITY; REAR SEAT HEIGHT)

       

 

 

    

Figure 8-4

Replacing the Camber Tube

Camber

Tube

Allen

Screw

Flats

Camber Tube

Mount

Adjusting the Rear Seat Height

(Aero Z Series 2 and ZRA Series 2)

Tools Needed:

•  3/16” Allen Wrench

1.  Note the original position of the camber tube clamp relative to the notches on the vertical strut.  See Figure 8-5.

2.  Remove the two Allen screws (one on each side) and washers that secure the camber tube clamps to the vertical 

struts.

3.  Reposition the camber tube clamp to the desired height.  Notches are 3/8” apart.  

 

Note:  Vertical struts come in three sizes, short, medium and long.  If you are not able to achieve the desired seat

 

height with your existing vertical strut, you may need to purchase longer or shorter struts.  

4.  Make sure the identical notches are used in each of the two vertical struts.

5.  Reinstall the two Allen screws (one on each side) and washers and securely tighten.

6.  Check the toe-in/toe-out and adjust as needed, and square the casters as needed.  See pages 8-8 and 8-9.

 

     

 

          

Figure 8-5

Adjusting the Rear Seat Height

Vertical Strut

Notches

Camber Tube 

Clamp

Washer

Allen Screw

Summary of Contents for AERO Z




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands