Ti Lite AERO Z Owner'S Manual Download Page 125

Page: 125 / 147

13-5

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 13: ANTI-TIPS

Receiver

Mounting

Plate

Figure 13-7

Engaging the Anti-Tips

Disengaging

To disengage the User-Friendly Rear Flip-Up Anti-Tip, grip the anti-tip receiver firmly and pull it downward, away from

the anti-tip mounting plate, and raise it until it re-engages in the mounting plate in the position shown in Figure 13-8.

Figure 13-8

Disengaging the Anti-Tips

Receiver

Mounting

Plate

Adjusting

To adjust the height of the User-Friendly Rear Flip-Up Anti-Tip, press the two release buttons on the telescoping lower

tube and adjust the height of the lower tube so that the wheel is within 1-1/2” to 2” off the ground. See Figure 13-9.

Figure 13-9

Adjusting the Anti-Tip

Release Button

Lower Tube

Upper

Tube

Receiver

Release Button

Mounting Plate

Summary of Contents for AERO Z




















































































































































Search results

Summary of Contents for AERO Z

Reviews:

Related manuals for AERO Z

Brands by name

Popular brands

Ti Lite AERO Z, Owner'S Manual

Search results

Summary of Contents for AERO Z

Reviews:

Related manuals for AERO Z

Brands by name

Popular brands