manualshive.com logo in svg

Ti Lite AERO Z, Owner'S Manual

Share
Download
Ti Lite AERO Z Owner'S Manual Download Page 77

7-5

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 7: 

BACK UPHOLSTERY, SEAT UPHOLSTERY AND SEAT 

CUSHIONS

Adjusting the Tension

Tools required:

•  1/8” Allen Wrench

1.  Remove the seat cushion.

2.  Detach the back upholstery from the seat upholstery (see “Velcro

®

-Style Adjustable Back Upholstery” on page 7-1 

or “Tension Adjustable by Straps Back Upholstery” on pages 7-2 and 7-3).

3.  Loosen, but do not remove, the Allen screws on the side of the seat upholstery where the adjustment flap is 

located on the underside of the seat upholstery.  See Figure 7-7.

4.  Detach the adjustment flap, adjust the seat upholstery to the desired tension, and re-secure the adjustment using 

the Velcro

®

-style material.

5.  Retighten the Allen screws that attach the seat upholstery to the frame.

6.  Reattach the back upholstery to the seat upholstery and replace the seat cushion.

 

     

 

    

Allen 

Screws

Adjustment

Flap

Figure 7-7

Adjusting/Replacing Bolt-On Seat Sling

Bolt-On

Seat Sling

Replacing the Upholstery

Tools required:

•  1/8” Allen Wrench

1.  Remove the seat cushion.

2.  Detach the back upholstery from the seat upholstery (see “Velcro

®

-Style Adjustable Back Upholstery” on page 7-1 

or “Tension Adjustable by Straps Back Upholstery” on pages 7-2 and 7-3).

3.  Remove all bolts that attach the seat upholstery to the chair frame.  See Figure 7-7.

4.  Remove the Bolt-On Seat Sling.

5.  If your replacement upholstery included new aluminum seat rails, proceed to Step 6.  If not, remove the aluminum 

seat rails from old upholstery and insert them into the new upholstery.

6.  Place the new seat upholstery on the frame and align the fastening holes in the upholstery and aluminum seat 

rails with the holes in the seat tubes of the frame.

7.  Loosely install all the bolts on the side of the seat sling where the adjustment flap is located.

8.  Install all the bolts on the opposite side of the seat sling and securely tighten.

9.  Detach the adjustment flap and adjust the seat upholstery to the desired tension.

10.  Fully tighten the bolts that attach the seat upholstery to the frame.

11.  Reattach the bottom of the back upholstery to the seat upholstery and replace the seat cushion.

Summary of Contents for AERO Z




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands