manualshive.com logo in svg

Ti Lite AERO Z, Owner'S Manual, Page: 101 / 147

Share
Download
Ti Lite AERO Z Owner'S Manual Download Page 101

11-1

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 11: CASTERS, FORKS AND CASTER PIN LOCKS

Standard Fork

I

WARNING

Always mount identical size casters and forks on both sides of your chair. 

 If you ignore this Warning, you may fall, tip 

over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

Replacing Casters

Tools Needed:

•  Two #2 Phillips Head Screw Drivers

1.  Remove the two Phillips Head screws, C Spring washers and axle that secure the caster to the fork.  Use one 

screw driver to hold one screw in place and a second screw driver to loosen the other screw.  See Figures 11-1 

through 11-5.

2.  Remove the caster and spacers from the fork.

3.  Install the new caster, spacers and C Spring washers onto the fork and securely tighten the two screws so there 

is no space between the caster, the spacers and the fork sides.  Use one screw driver to hold one screw in place 

and securely tighten the other screw with the second screw driver.

Note:  If your chair has 4” or 5” TiLite Performance casters, make sure that Spacer 2 (which is wider than Spacer 1) is

positioned on the recessed side of the caster, which should be oriented outwards when the casters are in the trailing

position.

I

WARNING

The threads on the screws that secure the casters to the fork are treated with Vibra-TITE

®

 VC-3, a locking and sealing 

coating, to reduce the possibility they will become loose.  You should be able to remove and reinstall these screws 

approximately four times without reapplying the coating.  If you repeatedly remove and reinstall these screws, TiLite 

requires that you reapply Vibra-TITE

®

 VC-3 after every fourth adjustment. 

 If you ignore this Warning, you may fall, tip 

over or lose control of the wheelchair and seriously injure yourself or others or damage the wheelchair.

    

Figure 11-1

Aero Z Series 1 Bearing Fork

Caster Cap

Fork

Washer
Nylock Nut

C Spring Washer

Phillips 

Head Screw

Caster

Spacer 2

Spacer 1

C Spring

Washer

Phillips

Head

Screw

Axle

Fork Stem

“Bullet” Caster 

Housing

Figure 11-2

ZRA Series 1 Bearing Fork

Caster Cap

Fork

Washer
Nylock Nut

C Spring Washer

Phillips 

Head Screw

Caster

Spacer 2

Spacer 1

C Spring

Washer

Phillips

Head

Screw

Axle

Fork Stem

“Bullet” Caster 

Housing

Summary of Contents for AERO Z




















































































































































Reviews:

No comments