manualshive.com logo in svg

Ti Lite AERO Z, Owner'S Manual

Share
Download
Ti Lite AERO Z Owner'S Manual Download Page 123

13-3

Z Series Owners Manual

OM_Z_1212RevC

CHAPTER 13: ANTI-TIPS

    

Figure 13-4

Mounting the Rear Anti-Tip Receiver

Allen Screw
Camber 

Clamp

Receiver

Allen

Screw

Camber Tube

Nylock Nut

Washer

Mounting

(ZR Series 2)

I

WARNING

Only an authorized TiLite dealer or qualified technician should install the rear anti-tip receiver.  

If you ignore this 

Warning, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others or damage the 

wheelchair. 

Tools Needed:

•  5/32” Allen Wrench

•  3/16” Allen Wrench

•  7/16” Open End Wrench

1.  Remove the rear wheels and place the frame upside down on a level surface.

2.  Remove the camber tube.  See “Replacing the Camber Tube (ZR Series 2)” on pages 8-7 and 8-8.

3.  Thread the Allen screw through the right side camber clamp, right side anti-tip receiver and washer and secure 

the nylock nut.  See Figure 13-5.

 

Note:  Make sure that the anti-tip receiver is oriented to be parallel to the floor.

4.  Repeat Step 3 on the left side camber clamp and left side anti-tip receiver.

5.  Reinstall the camber tube.  See “Replacing the Camber Tube (ZR Series 2)” on pages 8-7 and 8-8.

6.  Tighten the Allen screw in each anti-tip receiver so that it securely clamps into the camber tube.

7.  Reinstall the rear wheels.

Summary of Contents for AERO Z




















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands