Thermo Scientific VARIOKLAV 65 TC Operating Manual Download Page 78

Page: 78 / 85

15 Preparations for transport

(frost protection)

Thermo Scientific

50112712_082007_GB

15 Preparations for transport
(frost protection)

♦

Start the Empty Jacket program (P

program key).

The water from the double wall is now drained into the disposal system. This
process may take some time, depending on the operating state.

♦

Provide a collecting vessel (container,

bucket). Place the free hose end into the

collecting vessel.

♦

Press the coupling into the coupling socket

(1).

When the feed water tank has been
drained via the silicone hose:

♦

Press against the outer edge of the

coupling socket (1) with force: The

coupling disengages from the socket.

♦

Clean the removable drip ledge (2).

♦

Remove the residual water from the tank.

♦

Clean the sieve of the feed water tank under running water.

♦

Clean the entire sterilizing chamber as well as the feed water tank

thoroughly with a moist soft cloth.

Draining the vacuum pump

♦

Place the vessel below the screw cap (see picture).

Screw cap

Summary of Contents for VARIOKLAV 65 TC






















































































Search results

Summary of Contents for VARIOKLAV 65 TC

Reviews:

Related manuals for VARIOKLAV 65 TC

Brands by name

Popular brands

Thermo Scientific VARIOKLAV 65 TC, Operating Manual

Search results

Summary of Contents for VARIOKLAV 65 TC

Reviews:

Related manuals for VARIOKLAV 65 TC

Brands by name

Popular brands