Thermo Scientific VARIOKLAV 65 TC Operating Manual Download Page 82

Page: 82 / 85

17 Opening the door without power

Thermo Scientific

50112712_082007_GB

17 Opening the door without power

DANGER

Only use the emergency unlocking aid to open the sterilizer
door when the sterilizing chamber is not under pressure.

♦

Check to ensure that the sterilizing chamber is not under pressure.

Slightly jolt the door. If it is possible to move the door back and forth a bit, the
sterilizing chamber is not under pressure.

♦

Remove the cover for the emergency unlocking aid insertion opening.

♦

Insert the emergency unlocking aid in the emergency unlocking

aid insertion opening (see Figure 28).

Figure 28: Emergency unlocking aid insertion opening

♦

Fasten the hook of the emergency unlocking aid to the eye of the lock

barrel (not visible from outside).

♦

Pull the emergency unlocking aid.

The door opens.

♦

Remove the emergency unlocking aid and attach the insertion cover.

When the sterilizer is reconnected to mains, the sterilization phase display may
show an error message.

♦

Proceed as described in Chapter 14, Errors.

DANGER

If a program is interrupted, the load must be re-sterilized for
safety reasons.

Eye

Lock barrel

Summary of Contents for VARIOKLAV 65 TC






















































































Search results

Summary of Contents for VARIOKLAV 65 TC

Reviews:

Related manuals for VARIOKLAV 65 TC

Brands by name

Popular brands

Thermo Scientific VARIOKLAV 65 TC, Operating Manual

Search results

Summary of Contents for VARIOKLAV 65 TC

Reviews:

Related manuals for VARIOKLAV 65 TC

Brands by name

Popular brands