Thermo Scientific VARIOKLAV 65 TC Operating Manual Download Page 63

Page: 63 / 85

10 Settings

Thermo Scientific

50112712_082007_GB

INFORMATION

The sterilizer preheats the double wall as long as the
Preheating key (23) is activated. When preheating, the sterilizer
will not go into standby mode.
No feed water is utilized for this process.

If you want to perform another sterilization cycle:

INFORMATION

Turn the Preheating key (23) off in order to be able to use the
sterilizer. No programs can be selected while the Preheating
key (23) is activated.

♦

Press the Preheating key (23) on the control panel (6).

The indicator light in the corner of the Preheating key (23) goes off.

The door is automatically unlocked.

♦

Open the door (1).

You can now perform another sterilization cycle.

When the sterilizer is not busy with a sterilizing program and the Preheating key is
deactivated, it will go into standby mode after 5 minutes.

Summary of Contents for VARIOKLAV 65 TC






















































































Search results

Summary of Contents for VARIOKLAV 65 TC

Reviews:

Related manuals for VARIOKLAV 65 TC

Brands by name

Popular brands

Thermo Scientific VARIOKLAV 65 TC, Operating Manual

Search results

Summary of Contents for VARIOKLAV 65 TC

Reviews:

Related manuals for VARIOKLAV 65 TC

Brands by name

Popular brands