manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 91

 

17 

Absorbance Ratio

Measuring Samples

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

81

To measure samples automatically (using Auto 6 or Auto 3)

1. Install the blank and samples. 

2. Press 

Enter

.

To measure samples manually (using Manual 6 or Single Cell Holder)

1. In the Absorbance Ratio screen, press 

Run Test

.

2. Install the blank and sample.

A 6-Position Cell Holder can hold five samples.

3. Press 

Measure Blank

. 

If a 6-Position Cell Holder is installed, it moves to the B position to measure the blank 
and returns to its previous position.

4. Press 

Measure Sample

. 

If a 6-Position Cell Holder is installed, press the cell position buttons to reposition the cell 
holder and measure the rest of the samples manually.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands