manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 107

 

20 

Concentration Measurements—Standard Curve Application

Editing a Standard Curve

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

97

All absorbance measurements are removed from the screen.

To reset standards

1. With the standard curve displayed, press 

Edit Standards

.

2. Highlight 

Reset Standards

 and press 

Enter

.

All standards and measurements are removed from the screen.

To select a different curve fit for a standard curve

1. With the standard curve you want to edit displayed as a graph, press 

Change Fit

.

2. Highlight the curve fit to use for the standard curve and press 

Enter

. 

The instrument applies the selected curve fit to the data and displays the new fit.

Note  

To change the curve fit for a standard curve, you must display the standard curve as 

a graph, not as a table.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands