manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 122

22

 Performance Verification

Resolution (UV-Vis only)

112

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

If the test fails, follow these guidelines:

• Repeat the test twice to verify that the test is failing consistently.

• Contact technical support for more troubleshooting advice.

Resolution (UV-Vis only)

This test measures the ability of the spectrophotometer to resolve adjacent features in a 
spectrum. The test is performed using a 0.02% (v/v) solution of toluene in hexane and 
requires a hexane blank.

When running the internal standard test, remember that the wavelengths and tolerance values 
are preset and cannot be changed.

To run the Resolution test

1. Highlight 

Resolution

 and press 

Enter

.

Ensure that hexane is in the blank position and toluene in hexane is in cell 1.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands