manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 50

10

 Water Analysis Application

Running a Water Test

40

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Close the lid and press the function key under the Measure Blank option. The instrument will 
set the measurement wavelength and perform a blank measurement. Open the lid and remove 
the blank.

Place the cuvette, vial or tube containing your sample in the sample holder, close the lid and 
press the function key under the Measure Sample option. The screen will display the result as 
shown below.

Note  

When running a reverse color test, a reagent blank will also be required in addition 

to the normal blank. Insert the reagent blank if necessary and press the function key under 
the Rgnt Blank option. Open the lid and remove the reagent blank.

Note  

If you set Statistics to OFF in the test parameters screen, no Average or Std Dev 

information will be displayed.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands