manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 31

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

21

5

Cell Correction

Every test setup screen provides access to Cell Correction.

Before running Cell Correction:

• Clean the inside and outside of all the cells to be matched.

• Fill the cells with distilled water (or other blank solution), and place them in the sample 

compartment (see 

“Selecting and Positioning Cuvettes” 

on 

page 5

). Place the blank 

cuvette in Cell “B” of the cell changer.

Cell Correction

To run Cell Correction

1. Load the test type or stored test.

2. If Cell Correction is not visible, highlight 

More parameters

 and press 

Enter

.

Note  

 Cell Correction is not active from the Main (Basic ATC) screen.

Note  

 Cell Correction is active only when the 6-Position Cell Holder is set to either 

Auto 6 or Auto 3. The feature is not active when the cell holder is set to 1-Cell or Manual 
6, nor when the Single Cell Holder is installed.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands