Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 133

Page: 133 / 148

Maintenance

Replacing the Tungsten Lamp

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

123

5. Use a flat-blade screwdriver to remove the fuse holder.

6. Unsnap both fuses to remove them.

7. Insert the new fuses, pushing them in so they snap into place.

8. Replace the fuse cover.

9. Replace the power cord.

10. Plug the instrument back in to the wall outlet or power strip and turn on the power.

Replacing the Tungsten Lamp

Note

If the fuse blows again, contact your distributor or technical support.

WARNING

This lamp gets very hot during operation. Before removing the lamp, turn off

the instrument and allow the lamp to cool for 10 minutes.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Search results

Summary of Contents for Orion AquaMate 7000 Vis

Reviews:

Brands by name

Popular brands

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Search results

Summary of Contents for Orion AquaMate 7000 Vis

Reviews:

Brands by name

Popular brands