manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 143

 

24 

Parameters

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

133

Select Test

Tags the highlighted test name with “>” to include the test in 
the SmartStart menu
(Utility Stored Tests Directory)

Set Max. X

Set Min. X

Sets the cursor position in the graph as the minimum X and 
the maximum X values for recalculating rate 
(Kinetics)

Set nms

Lets you enter and edit the wavelength and factor values

Set Options

Selects the factor entry or the baseline to calculate area under 
the peak in the graph 
(Scanning)

Setup correction

Initiates the procedure to collect the data necessary to correct 
for absorbance differences between cuvettes
(all test types)

Slope

Enters ?Abs/?Concentration value
(Standard Curve test type)

Smoothing

Turns data smoothing on and off
(Scanning)

Software Revision

Displays the version of firmware in the instrument
(Utility)

SRE tolerance

Acceptable minimum stray light

Standard Concentrations

Enters the concentration of standards used to generate the 
standard curve for the test

Standby

Selects the time since the last keystroke or instrument activity; 
powers down the unit to save lamp life
(Utility)

Start wavelength

Enters the beginning wavelength for a scan
(Scanning tests only)

Statistics

Turns stats on or off; if ON, calculates the average and Std Dev 
of results; Statistics registers are cleared when Statistics = OFF 
and/or when instrument is OFF, and/or when test parameters 
are changed, and/or when test is saved (or resaved)
(in all test types except Kinetics, Scanning, Multiwavelength)

Std Concentration

Enters the concentration of the analyte in the standard 
solution

Stop wavelength

Enters the ending wavelength for a scan
(Scanning tests only)

Stored Tests Directory

Displays the list of tests stored in the instrument
(Utility)

Parameter

Description

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands