manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 23

Thermo Scientific

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

13

3

Accessories

This chapter briefly describes the sampling and system accessories that are available for your 
spectrophotometer. Complete descriptions and operating instructions are included with the 
accessories.

You can install or remove these accessories without switching off the instrument.

Cell Holders and Cell Holder Accessories

The AquaMate is shipped with a custom cell holder that accommodates a vial up to 25 mm in 
diameter, a rectangular cell up 50 mm long, or a 10 mm pathlength square cuvette. An 
additional single cell platform and 6-cell carousel for 10 mm square cells is included with the 
Orion AquaMate 8000 UV-Vis.

Cell Holder Configurations

The following table shows the available cell holders and their accessories. You can install or 
remove accessories without switching off the instrument.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands