manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 138

24

 Parameters

128

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Calculator

Enables the calculator mode
(Utility)

Cell Correction

Selects the option to automatically correct for variances in 
absorption between the cuvettes 
(all test types)

Cell Position #

Displays the position placed in the light path
(only with auto turret)

Change Mode
Change to Abs
Change to %T

Switches measurement modes 
(Basic A-%T-C and some Performance Verification tests)

Collect Baseline

Starts the collection of the baseline
(Scanning only)

Concentration

Sets the concentration value

Conc of Standard

Displays the entered concentration value
(Adv A-%T-C)

Correction Mode

Selects the mode for cell correction 
(Discrete nms or Scan)

Cursor 

Goes to Cursor tracking mode to view data points in the graph
(Kinetics, Scanning)

Cursor 

→

←

 

Cursor

Moves the cursor right or left on the graph and displays the 
data of each point
(Kinetics, Scanning)

Curve Fit

Selects the type of line fit calculation
(Standard Curve tests)

Data File Name

Allows entry of a name for the data file when AutoSave = ON

Date Cell Correction

Displays the date when cell correction data on cuvettes was last 
collected

Date Standards Measured

Displays the date when standards were last measured with this 
instrument
(Standard Curve tests)

Date/Time Setup

Enters the current date and time settings for the instrument
(Utility)

Delay Time

Enters the time from Test Initiation to first measurement; 
allows for sample equilibration
(ADV. A-%T-C and Kinetics)

Delete Character

Deletes the last character of Name entry
(Test Name and Edit [Units])

Parameter

Description

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands