manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 16

1

 Spectrophotometer Basics

Z-dimensions

6

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Other Guidelines

Position cuvettes and test tubes so that the clear sides face the light beam, one clear side facing 
the front of the instrument and the other facing the back.

When using small aperture (small volume) cells:

• Always used cells with black masking

• Use the same cell (or cuvette) for your blank and your samples

Z-dimensions

The figure below illustrates the position of the light beam in the instrument.

Beam size specifications are shown below.

• Distance from bottom of cuvette to center of beam (Z-dimension): 8.5 mm

• Beam dimensions: 2 mm (wide) by 7 mm (tall)

Note  

The pathlength of test tubes is not as well defined as that of square cuvettes.

Note  

Always place test tubes in the instrument in exactly the same orientation in the light 

beam. An alignment mark on the test tube helps you orient the test tubes consistently and 
correctly.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands