Thermo Scientific Haas Mini Mill User Manual Download Page 60

Page: 60 / 68

Chapter 4

Alarms Management

User Manual - Haas Mini Mill

AA83766

Sample support movement impossible

Explanations

Conditions for the movement of the sample support are missing

Acknowledge

By the operator

Corrections

♦

Check that the position value and offset are correct

Remarks

Timeout sample support positionning

Explanations

The step motor of the sample support did not get in position within the timeout

Acknowledge

By the operator

Corrections

♦

Check the motor

Remarks

Height measurement error

Explanations

There is no sample on the sample support or it is smaller than 8 mm or greater that the
measurement range of the sample support

Acknowledge

By the operator

Corrections

♦

Check that there is a samplée on sample support

♦

Check the sensor on the clamp

Remarks

Défault on the robot door opening

Explanations

During the opening of the robot door, the upper sensor did not activated within the
tempo.

Acknowledge

By the operator

Corrections

♦

Check and set the upper sensor 42B5 on the piston 202A2

♦

Check the temporisation "To – alarm robot door open default"

♦

Operate the robot door manually to check the good functionning of it

Remarks

Summary of Contents for Haas Mini Mill





































































Search results

Summary of Contents for Haas Mini Mill

Reviews:

Related manuals for Haas Mini Mill

Brands by name

Popular brands

Thermo Scientific Haas Mini Mill, User Manual

Search results

Summary of Contents for Haas Mini Mill

Reviews:

Related manuals for Haas Mini Mill

Brands by name

Popular brands