Thermo Scientific Haas Mini Mill User Manual Download Page 44

Page: 44 / 68

Chapter 3

Dialogue Boxes Description

User Manual - Haas Mini Mill

AA83766

Editable fields:

Tempo

Description

To – default alarm for vice closed

On vice closed request, a tempo starts. If the vice is not closed

within this tempo, an alarm is displayed.

To – default alarm for vice open

On vice open request, a tempo starts. If the vice is not open within

this tempo, an alarm is displayed.

T – aknowledge vice closed

On vice closed request and aknowledge of To, this tempo starts,

once over, the closing cycle is aknowledged.

T - aknowledge vice open

On door open request and aknowledge of To, this tempo starts,

once over, the opening cycle is aknowledged.

T – reserve

Not used

T – Collector cleaning

set the time needed to evacuate the collector belt. Only with

collector option.

♦

In operator mode, the tempo can not be modified.

SETTING 5/8 : Holders delays

Figure 3.13

Summary of Contents for Haas Mini Mill





































































Search results

Summary of Contents for Haas Mini Mill

Reviews:

Related manuals for Haas Mini Mill

Brands by name

Popular brands

Thermo Scientific Haas Mini Mill, User Manual

Search results

Summary of Contents for Haas Mini Mill

Reviews:

Related manuals for Haas Mini Mill

Brands by name

Popular brands