Thermo Scientific Haas Mini Mill User Manual Download Page 58

Page: 58 / 68

Chapter 4

Alarms Management

User Manual - Haas Mini Mill

AA83766

Alarms List

All alarms managed by the system are listed below with:

♦

Alarm number.

♦

The alarm texte corresponding to the display on the screen.

♦

The category of thealarm.

♦

An explination of the alarm.

♦

Correcting action.

♦

Possible remarkses.

Power off or emergency stop

Explanations

Power off
Controled by input I0.0

Acknowledge

Automatic when powered on

Corrections

♦

Check whether other messages are displayed and take actions

♦

Check that no ES are pressed

♦

Check that either the door (relay 32K0) or robot door (relay 33K0) is closed

♦

Ccheck that the PLC output Q10.1 (PLC OK) is activated. If not, a message should
explain the reason.

♦

Check that the relays 30K7 and 30K8, driven by Q10.1 output are activated.

♦

Check if the 30K4 and 30K5 relays (ES) are ok.

♦

Check if the 30K0 relay is ok.

Remarks

Amplifier default

Explanations

The sample support amplifier is in error

Acknowledge

By the operator

Corrections

♦

Check 10Q6 circuit breaker

♦

Check RDY and COM led on the amplifier 10A3

♦

Check that the sample support did not hit anything

Remarks

Summary of Contents for Haas Mini Mill





































































Search results

Summary of Contents for Haas Mini Mill

Reviews:

Related manuals for Haas Mini Mill

Brands by name

Popular brands

Thermo Scientific Haas Mini Mill, User Manual

Search results

Summary of Contents for Haas Mini Mill

Reviews:

Related manuals for Haas Mini Mill

Brands by name

Popular brands