manualshive.com logo in svg

Themis RES-32XR3-S, Installation Manual

Share
Download
Themis RES-32XR3-S Installation Manual Download Page 50

RES-32XR3-S  for X8DTL-6/6F Installation Manual

2-2

Themis Computer

follows:

1.

Loosen the two captive Phillips screws holding the protective top access cover
to the rear of the RES-32XR3-S  for X8DTL-6/6F chassis (see 

A

, 

Figure 2-1

). 

2.

Both the front and sides of the cover have flat hooks or tabs underneath that
fit under slots on the chassis top edges (see 

B

, 

Figure 2-1

). Remove the cover

by sliding it toward the rear until it is free of these chassis slots. 

3.

Store the cover in a safe place until it is replaced.  

Figure 2-1.  

Remove the RES-32XR3-S  for X8DTL-6/6F Protective Access Cover

Loosen the 2 captive access-cover screws... 

A

B

Rear View

... and slide the top cover toward the rear until the top hooks and tabs clear all chassis slots

Chassis slot

Chassis slot

Left-side top edge

Summary of Contents for RES-32XR3-S



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands