manualshive.com logo in svg

Themis RES-32XR3-S, Installation Manual

Share
Download
Themis RES-32XR3-S Installation Manual Download Page 112

A-4

Themis Computer

RES-32XR3-S  for X8DTL-6/6F Installation Manual

A.5

Gigabit Ethernet LAN Ports

The RES-32XR3-S supports two RJ45 Gigabit Ethernet LAN port connectors (LAN
1 and LAN 2), each with two embedded LEDs (see 

Figure A-4

). 

Pinout signal descriptions are listed in 

Table A-5

. 

 

 

A.6

IPMI Dedicated LAN Port (X8DTL-6F Only)

The single IPMI dedicated Ethernet LAN port on the RES-32XR3-S rear I/O panel
has identical pinout and signal descriptions as the LAN 1 and LAN 2 Ethernet ports
described in the previous Section A.5, “Gigabit Ethernet LAN Ports”.

Figure A-4.  

Ethernet Connector, Type RJ45

Table A-5.  

RJ45 Ethernet Pinout Signals

Pin

Signal Name

Pin

Signal Name

1

TRD0+

5

TRD2-

2

TRD0-

6

TRD1-

3

TRD1+

7

TRD3+

4

TRD2+

8

TRD3-

• 

The color of the left LED indicates the LAN connection speed:

— Off = 10 MHz
— Green = 100 MHz
— Amber = 1 GHz

• 

The right LED, when lit, indicates LAN activity (network traffic).

1

8

Link Speed

Network Traffic

Summary of Contents for RES-32XR3-S



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands