manualshive.com logo in svg

Texas Instruments TMS320C3x, User Manual

The Texas Instruments TMS320C3x, known for its exceptional performance and versatility, heralds a new era in signal processing technology. Unlock the full potential of this remarkable product by accessing the comprehensive User Manual that can be easily downloaded for free from manualshive.com.

Share
Download
background image

Bus Timing

10-43

TMS320C32 Enhanced External Memory Interface

Figure  10–27 illustrates a zero wait-state read and write sequence for IOSTRB
active. During writes, the data is valid when IOSTRB changes.

Figure 10–27. Zero Wait-State Read and Write Sequence for IOSTRB Active

Write

Read

IOSTRB

RDY

D

A

R/W

H1

H3

Figure 10–28 depicts a one wait-state read sequence for IOSTRB active.
Figure 10–29 shows a one wait-state write sequence for IOSTRB active. For
each wait-state added, IOSTRB, R/W, and A are extended for one extra clock
cycle. Writes hold the data on the bus for one extra clock cycle. RDY is sampled
on each extra cycle and the sequence is terminated when RDY is low.

Summary of Contents for TMS320C3x






















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TMS320C3x

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
LaCie d2 Network 2 Quick Install Manual preview
d2 Network 2
Brand: LaCie Pages: 44
LaCie LaCie Ethernet Disk Datasheet preview
LaCie Ethernet Disk
Brand: LaCie Pages: 2
LaCie SATA II ExpressCard 34 Datasheet preview
SATA II ExpressCard 34
Brand: LaCie Pages: 2
LaCie 12big Rack Fibre 8 Quick Install Manual preview
12big Rack Fibre 8
Brand: LaCie Pages: 9
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Brand: Lattice Semiconductor Pages: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Brand: Lattice Semiconductor Pages: 13
Intel Optane M Series Installation And User Manual preview
Optane M Series
Brand: Intel Pages: 59
DAD DPX2060 User Manual preview
DPX2060
Brand: DAD Pages: 32
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Brand: e-con Systems Pages: 9
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Brand: RuggedCom Pages: 42
TDK HHM Series HHM2411 Specification Sheet preview
HHM Series HHM2411
Brand: TDK Pages: 2
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Brand: QNAP Pages: 54
G&D DL-DVI-Vision-IP Series Installation And Operation Manual preview
DL-DVI-Vision-IP Series
Brand: G&D Pages: 228

Brands by name

Popular brands

Load more brands