background image

2

www.teejet.com

Radion 8140 automatic sprayer control

NO.2 OPERATION SCREEN

Boom sections

Spray status

Pressure gauge

Current nozzle

Information bar

Current droplet size

Tank contents / filling options

Alarm warning

Options tab

Application rate change

►Information bar – displays application rates and selectable 

information

►Current nozzle – displays current nozzle and accesses five (5) 

preset nozzle types

►Application rate change – displays rate changes (if in 

Automatic regulation mode)

►Tank – displays remaining tank contents and accesses filling 

options

◄Filling – establishes actual/desired tank material/density

►Alarm warning – displays active alarm conditions
►Options tab

 

 – accesses the Operation menu

◄Displays Home button

 

, Close Menu button

 

regulation modes and target rate options

►Pressure gauge – displays current pressure range compared 

with recommended pressure range

◄Droplet size – displays selected droplet size

►Boom sections – displays configured boom sections

◄Spray status – displays active/inactive for section

Operation menu

The Options tab is always available on the Operation screen. This 

tab accesses the Operation menu where the Home button, regulation 

modes and target rate options display.

Operation menu buttons

Home

Auto

reg

Man

reg

Change between automatic/manual regulation 

modes

Automatic regulation mode

5%

Target rate boost percent increase

5%

Target rate boost percent decrease

0%

Return to target rate

Manual regulation mode

Regulation valve manual open

Regulation valve manual close

Close menu

Figure 2: Options tab – Automatic mode 

0%

Man

reg

5%

5%

Regulation mode

Target rate reset

Boost/step percent increase

Boost/step percent decrease

Home

Close menu

Figure 3: Options tab – Manual mode 

Auto

reg

Regulation mode

Valve open

Valve close

Home

Close menu

Summary of Contents for RADION 8140





























Reviews: