TechVision PS8E1N2 Manual Download

Page: 84 / 121

Alarm Management

DVR User Manual

interface. Set the e-mail address of the recipients. See 11.1.5 E-mail Configuration for details.

9.5.3 Display

Click Start



Settings



Alarm



Event Notification



Display to go to the display configuration

interface. Set the duration time of the pop-up video and the pop-up message box. Click
“Apply” to save the settings.

9.5.4 Buzzer

Click Start



Settings



Alarm



Event Notification



Buzzer to go to the buzzer configuration

interface. Set the delay time of the buzzer and then click “Apply” to save the setting. You can
click “Test” to test the buzzer.

9.5.5 Push Message

Click Start



Settings



Alarm



Event Notification



Push Message to go to the interface as

shown below. Check “Enable” and then click the “Apply” button to save the settings. If Push
Server is online, it will push messages to the mobile clients.

Summary of Contents for PS8E1N2


























































































































Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands

TechVision PS8E1N2, Manual

Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands