TechVision PS8E1N2 Manual Download

Page: 17 / 121

Basic Operation Guide

DVR User Manual

Button

Function

Power Button

Switch off—to stop the device

Record Button

To start recording

-/-- /0-9

Input number or choose camera

Fn1 Button

Unavailable temporarily

Multi Button

To choose multi screen display mode

Next Button

To switch the live image

SEQ

To go to sequence view mode

Audio

To enable audio output in live mode

Switch

No function temporarily

Direction button

To move cursor in setup or pan/title PTZ

Enter Button

To confirm the choice or setup

Menu Button

To go to menu

Exit Button

To exit the current interface

Focus/IRIS/Zoom/PTZ

To control PTZ camera

Preset Button

To enter into preset setting in PTZ mode

Cruise Button

To go to cruise setting in PTZ mode

Track Button

No track function temporarily

Wiper Button

No function temporarily

Light Button

No function temporarily

Clear Button

No function temporarily

Fn2 Button

No function temporarily

Info Button

Get information about the device

To control playback. Play(Pause)/Stop/Previous
Frame/Next Frame/Speed Down/Speed Up

Snap Button

To take snapshots manually

Search Button

To go to search mode

Cut Button

No function temporarily

Backup Button

To go to backup mode

Zoom Button

To zoom in the images

PIP Button

No function temporarily

Note:

You shall press P.T.Z button to enter PTZ setting mode, choose a channel and press P.T.Z button again to

hide the P.T.Z control panel. Then you can press preset, cruise, track, wiper or light button to enable the

relevant function.

Summary of Contents for PS8E1N2


























































































































Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands

TechVision PS8E1N2, Manual

Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands