TechVision PS8E1N2 Manual Download

Page: 62 / 121

Playback & Backup

DVR User Manual

Playback & Backup

8.1 Instant Playback

Click

on the tool bar at the bottom of the preview camera window to play back the record

(click

on the tool bar at the bottom of the live preview interface to set the default playback

time). Refer to the picture below. Drag the playback progress bar to change the playback time.
You can also click the right-click menu “Instant Playback” in the camera window and then set
the instant playback time to play back the record.

8.2 Playback Interface Introduction

Click

on the tool bar at the bottom of the live preview interface or click Start



Playback

to go to the playback interface as shown below (click

on the tool bar at the bottom of the

live preview interface to set the default playback time).

Summary of Contents for PS8E1N2


























































































































Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands

TechVision PS8E1N2, Manual

Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands