TechVision PS8E1N2 Manual Download

Page: 78 / 121

Alarm Management

DVR User Manual

③

Click “Apply” to save the settings. You can click “Article Protect Config” to go to the

object detection configuration interface.

9.3.2 Exception

Exception Configuration

①

Click Start



Settings



Camera



Intelligent Detection



Exception to go to the following

interface.

②

Select the camera and enable the relevant detection as needed.

Scene Change

: Alarms will be triggered if the scene of the monitor video has changed.

Video Blurred

: Alarms will be triggered if the video becomes blurry.

Video Color Cast

: Alarms will be triggered if the video becomes obscured.

③

Set the sensitivity of the exception detection.

④

Click “Apply” to save the settings.

⑤

Click “Processing Mode” to go to the alarm handling configuration interface of exception

detection.

Exception Alarm Handling Configuration

①

Click Start



Settings



Alarm



Intelligence Alarm



Exception to go to the interface.

Summary of Contents for PS8E1N2


























































































































Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands

TechVision PS8E1N2, Manual

Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands