TechVision PS8E1N2 Manual Download

Page: 115 / 121

FAQ

DVR User Manual

109

Q6.

The system cannot record, why?

Make sure the HDD was formatted prior to use.

The record schedule has not been set in manual record mode. Please refer to 7.3.2 Record

Schedule Configuration for details.
c.

Maybe HDD is full and thus the DVR is not able to record. Check HDD information from

Disk Management and if required, please enable the recycle function (please see 7.1.2
Advanced Configuration for details).
d.

There is no disk but cameras in the disk group, so please add at least one disk to the group.

Refer to 7.5.1 Storage Mode Configuration for details.
e.

The HDD could have gone bad. Please change another one.

Q7.

Fail to access the DVR remotely through IE.

Please make sure the IE version is IE8 or above.

Please check whether the PC has enabled the firewall or installed the antivirus software.

Please try to access the DVR again after you disable the firewall and stop the antivirus
software.
c.

Black & white list may have been set in Account and Authority setting. The PC of which

the IP address is in the black list or out of the white list cannot access the DVR remotely.

Q8.

ActiveX control cannot be downloaded. How can I do?

IE browser blocks ActiveX control. Please do setup as per the steps mentioned below.

①

Open IE browser. Click



Internet Options.

Summary of Contents for PS8E1N2


























































































































Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands

TechVision PS8E1N2, Manual

Search results

Summary of Contents for PS8E1N2

Reviews:

Related manuals for PS8E1N2

Brands by name

Popular brands