Technosoft iPOS4808 MX Series Technical Reference Download Page 24

Page: 24 / 114



Technosoft 2014

iPOS4808 MX Technical Reference

Figure 2.7.

Brushless AC linear motor with linear Hall signals.

Position / speed / torque control.

8. Position, speed or torque control of a

brushed

rotary motor

with an

incremental

quadrature encoder

on its shaft. Scaling factors take into account the transmission ratio

between motor and load (rotary or linear). Therefore, the motion commands (for position,
speed and acceleration) expressed in SI units (or derivatives) refer to the load

, while the

same commands, expressed in IU units, refer to the motor.

Figure 2.8.

DC brushed rotary motor. Position / speed / torque control.

Quadrature encoder on motor.

9. Load position control using an

incremental quadrature encoder

on load, combined with

speed control of a

DC brushed

rotary motor

having a

tachometer

on its shaft. The

motion commands (for position, speed and acceleration) in both SI and IU units refer to
the load.

Figure 2.9.

DC brushed rotary motor. Position / speed / torque control.

Quadrature encoder on load plus tachometer on motor.

Motion commands can be referred to the motor by setting in EasySetUp a rotary to rotary transmission with ratio 1:1

Summary of Contents for iPOS4808 MX Series



















































































































Search results

Summary of Contents for iPOS4808 MX Series

Reviews:

Related manuals for iPOS4808 MX Series

Brands by name

Popular brands

Technosoft iPOS4808 MX Series, Technical Reference

Search results

Summary of Contents for iPOS4808 MX Series

Reviews:

Related manuals for iPOS4808 MX Series

Brands by name

Popular brands